Pleated Sediment & CTO Carbon Replacement Pack — 10″ × 4.5″
Less grit. Fresher-tasting water.
Refresh two working stages with one matched 10″ × 4.5″ replacement pack. A pleated sediment cartridge handles incoming particles, while CTO carbon helps reduce chlorine taste and unwanted odour.
Who this pack is for
Dual 10" x 4.5" Systems - Time for fresh filters.
When did you last replace your filters? A fresh set helps restore better taste, reduce chlorine smell and keep scale more manageable.
𝗪𝗲 𝗿𝗲𝗰𝗼𝗺𝗺𝗲𝗻𝗱 𝗿𝗲𝗽𝗹𝗮𝗰𝗶𝗻𝗴 𝗮𝗹𝗹 𝘁𝗵𝗿𝗲𝗲 𝗳𝗶𝗹𝘁𝗲𝗿𝘀 𝗲𝘃𝗲𝗿𝘆 𝟲–𝟭𝟮 𝗺𝗼𝗻𝘁𝗵𝘀, 𝗱𝗲𝗽𝗲𝗻𝗱𝗶𝗻𝗴 𝗼𝗻 𝘄𝗮𝘁𝗲𝗿 𝗾𝘂𝗮𝗹𝗶𝘁𝘆 𝗮𝗻𝗱 𝘂𝘀𝗲. 𝗖𝗵𝗲𝗰𝗸 𝘀𝗼𝗼𝗻𝗲𝗿 𝗶𝗳 𝗰𝗵𝗹𝗼𝗿𝗶𝗻𝗲 𝘁𝗮𝘀𝘁𝗲, 𝘀𝗰𝗮𝗹𝗲 𝗼𝗿 𝗽𝗿𝗲𝘀𝘀𝘂𝗿𝗲 𝗹𝗼𝘀𝘀 𝗿𝗲𝘁𝘂𝗿𝗻𝘀.
Particles in the incoming water
The pleated cartridge catches dirt, rust and sand before water reaches the carbon stage.
Enjoy every sip
No more chlorine taste and unpleasant odours for better-tasting water straight from your tap.
What's in the pack
What arrives in your replacement pack.
Stage 01Pleated Sediment Replacement Filter — 10″ × 4.5″, 5 Micron
The pleated cartridge provides another sediment-filtering surface in this supplied set.
Stage 025 Micron CTO Carbon Block Filter — 10″ × 4.5″
The carbon block targets chlorine taste, odour and other adsorbable compounds.
Measure these two.
Measure the cartridge you're replacing, not its housing.
Will it fit?
Match the cartridge format and the working parts.
Compare your current filters’ length, diameter, end openings and seals. A matching nominal size is a starting point; confirm the complete fit with HFS before ordering.
Measured it and still not sure?
Send a photo of the cartridge beside a tape measure and we'll tell you which size it is.
Call 1300 264 173 or email sales@homefiltrationsystems.com.
Nominal sizes vary a little between makers, so match the measurement rather than the label. What we can't tell you is how ours compares to a cartridge we didn't make and haven't tested, or whether a replacement affects your housing's own warranty; that one is between you and its manufacturer.
Fitting it, what comes out, and when it's due again
A straightforward cartridge change, with the right fit.
Need help with the change? Call 1300 264 173.
What happens, in order
-
Identify & isolateCheck the exact replacements against your system guide. Isolate water, release pressure.
-
Remove & inspectRemove the old cartridges. Clean the housings and check seals.
-
Fit the matched partsSeat each cartridge in its specified position. Check openings and O-rings before refitting the bowls.
-
Restore, flush & checkRestore supply as directed, flush the cartridges and inspect for leaks. Record the change date.
Reviews
What people who fitted it said.
Only buyers we can match to an order can leave one, so the count is lower than it would be otherwise.